河北废钢剪切机厂

The main technical parameters of the heavy duty fast scrap shearing machine:

1、剪切刀长：1米。

1, cutting knife length: 1 meters.

2、剪切油缸规格：剪切油缸内径200-205毫米，剪切力可达100吨左右。

2, shearing cylinder specifications: shearing cylinder diameter of 200-205 mm, the shear capacity is up to 100 tons.

3、电机配置：18.5千瓦电机或22千瓦电机。

3, motor configuration: 18.5 kilowatt motor or 22 kilowatt motor.

4、高压油泵规格：100YCY或者160YCY高压柱塞泵。

4, high pressure oil pump specifications: 100YCY or 160YCY high pressure plunger pump.

5、剪切最大张口尺度：剪切最大张口为350毫米到400毫米。

5, the maximum shear opening scale: the maximum shear opening is from 350 mm to 400 mm.

6、剪切速度：每分钟8-10次剪切速度。

6. Shear speed: 8-10 shear speeds per minute.

7、剪切废钢种类：槽钢、工字钢、煤矿小道轨、角钢、汽车拆解大梁、螺纹钢、船板、普板厚度30毫米，圆钢直径600-700毫米等都可剪切。剪切厚度越厚剪切宽度越窄。

7, shear scrap type: channel steel, I-steel, coal mine track, angle steel, car disassembly beam, screw steel, ship plate, 30 millimeter thickness of the plate, 600-700 mm diameter of the round steel can be cut. The thicker the shear thickness, the narrower the shear width is.

（1）采用液压驱动，操作方便，维修简单。适用范围广，工作效率高、主机即可以安装于室内也可以安装在室外。

(1) hydraulic drive is easy to operate and easy to maintain. It has wide application and high efficiency. The main engine can be installed indoors or outdoors.

（2）工作刀口长度：500mm-1200mm,剪切力从60吨至250吨。适用不同规模，不同要求用户选择。

(2) the length of the knife edge is 500mm-1200mm, and the shear force is from 60 tons to 250 tons. It is suitable for different sizes and requires users to choose.

（3）安装无须底脚螺丝，无电源的地方可用柴油机作动力。

(3) no foundation bolts for installation, where the available diesel engine without power supply for power.

安全操作规程:

Safe operation procedure:

(1)设备应定人操作，其他人未经培训不得任意使用。

(1) equipment should be operated by others, and others can't be used without training.

(2)开车前应检查各部位是否正常，紧固件是否牢固。

(2) before driving, check whether the parts are normal and whether the fasteners are solid.

(3)禁止剪切未经退火的钢件、铸铁件、软质金属件、过薄的工件、长度小于100毫米的工件，以及超过剪刀长度的工件。 

(3) it is forbidden to cut unannealed steel, cast iron, soft metal parts, thin pieces, work pieces of less than 100 millimeters in length, and work pieces that exceed the length of scissors.  

(4)操作时，人体不准接近设备的传动部分及刀口，并应注意周围人员的安全，防止料翘起伤人。剪切时应尽量将料靠近刀里边剪切。剪较短料时，不得用手持工件送料，应采用夹钳送料。 

(4) when operating, the human body is not allowed to approach the transmission part and the knife edge of the equipment, and the safety of the people around it should be paid attention to, so as to prevent the material from rising and hurting people. When cutting, the material should be cut near the edge of the knife as far as possible. When cutting short material, no hand-held workpiece shall be used for feeding, and the clamp shall be used for feeding.  

(5)设备运转时，操作人员不得擅自离开岗位，工作完毕或暂离岗位时，应切断电源。

(5) when the equipment is running, the operator must not leave the post without permission. When the work is completed or temporarily leave the post, the power shall be cut off.