1、 操作人员应认真执行设备日常维护保养的规定。开机前应仔细检查设备电气线路、气动部分、机械部分有无异常、漏电、漏气及消音器堵塞现象；各紧固件是否牢固，传动链条是否正常，润滑油位是否符合要求，安全防护系统是否齐全可靠，确认无误后方可开机。

1, operators should conscientiously implement the provisions of equipment maintenance. The boot shall inspect the equipment electrical wiring, pneumatic parts, mechanical parts without exception, leakage, leakage and clogging of the fastener muffler; whether firmly, transmission chain lubrication oil level is normal, whether it meets the requirements, safety protection system is complete and reliable confirmation before starting.

2、 打开电源总开关、系统开关，空车试运转，搬动手动润滑把柄，润滑设备，班中润滑不得低于3次。

2, open the power switch, switch system, empty commissioning, move the manual lubrication handle, lubrication equipment, class lubrication shall not be less than 3 times.

3、 设置参数内剪切钢筋的直径和单次剪切根数，数据填写须准确完整。

3, set shear reinforcement parameters within a single shear diameter and root number, fill in the data must be accurate and complete.

4、 系统内的初始距离，出料距离和料仓转向须认真填写，否则，易造成设备损坏。

The initial distance of 4, system, discharge distance and steering bin should fill in, otherwise, easy to cause damage to the equipment.

5、 设置画面2的内容为原始数据，不必填写，不得随意改动其数据，如有需要，可微调。

5, 2 setting screen content to the original data, do not write, not free to change the data, if necessary, can be adjusted.

6、 剪切参数画面，剪切钢筋长度、总根数，待剪钢筋总长度的填写必须准确完整。

6, shear parameter picture, shear reinforcement length, total root number, to cut the total length of reinforcement fill must be accurate and complete.

7、 操作中，当手动送料时，禁止用手扶送料链条，以免发生危险。

7, operation, when the manual feeding, prohibit the use of hand feeding chain, in order to avoid danger.

8、 剪切机工作时产生的震动，易造成接近开关和磁性开关螺丝松动，影响设备运行动作，应注意观察，发现螺丝松动及时紧固。

From 8, when shearing machine vibration, easy to cause the proximity switch and the magnetic switch screw loosening, influence of equipment operation action, should observe, find timely fastening screws loose.

9、 操作中注意检查油水分离器的过滤情况，油位不得低于其下限；水位不得高于其上限，并及时将水放掉。

Check the filter separator 9, operation, the oil level shall not be lower than the lower limit; the water level shall not be higher than the upper limit, and keep the water off.

10、注意观察空压机气泵压力开关工作是否正常，如有异常及时排除。

10, pay attention to the observation of air compressor air pump pressure switch work is normal, if abnormal in time to exclude.

11、工作结束，关闭总电源和系统电源，清理设备的铁屑、灰尘，成品料、余料、废料归类规范放置，清理工作场所

11, when the work is finished, turn off the total power and system power, clean up the iron dust, dust, finished products, surplus materials and waste materials, and sort out the workplace.